Lenny/Dateiliste/sensors3.conf

Archiv: Dieser Artikel beschreibt nicht die Funktionalität des derzeit aktuellen delixs-Servers. Er beschreibt ältere Schulserver-Funktionen und dient dem Zweck der Archivierung.

/etc/sensors3.conf

Achtung: Bitte kopieren Sie diese Datei nicht, da sich die Hardware des Servers fast immer unterscheidet! Hinweise finden Sie unter: Entwicklungsumgebung/Sensors

Hinweis: Die im delixs-Schulserver geänderten Zeilen sind gelb unterlegt.

Sensors configuration file used by 'libsensors'
------------------------------------------------
#
PLEASE READ THIS HELPFUL HINT!!! #
#
The 'set' lines (generally for min and max values) #
do not take effect until you run 'sensors -s' as root !!! #
We suggest you put 'sensors -s' in a /etc/rc.d/... file #
to be run at boot time after the modules are inserted !!! #
#
OVERVIEW
--------
This configuration file will be used by all userspace applications
linked to libsensors. It is NOT used by the lm_sensors drivers directly.
This config file consists of two parts: the heavily commented LM78
example, and the real parts. Search for '####' if you want to skip
to the real stuff.
Hash marks introduce comments, which continue until the end of a line.
Identifiers consisting of only digits and letters can be used
unquoted; other identifiers must be quoted. Escape characters within
quotes operate like those in C.
CHIP LINES
----------
A 'chip' line specifies what the following 'label', 'compute', 'set' and
'ignore' lines refer to. In this case, until the
next 'chip' line, everything refers to all lm78 and lm79
chips. Other examples are *-isa-* for everything on the ISA bus, and
lm78-i2c-*-4e for all lm78 chips on address 0x4e of any I2C bus.
If more chip statements match a specific chip, they are all considered.
Later lines overrule earlier lines, so if you set the in0 label for
lm78-* to "This", and later on the in0 label for lm78-isa-* to "That",
"That" is used for LM78 chips on the ISA bus, and "This" for LM78
chips on a non-ISA bus.
chip "lm78-*" "lm79-*"
FEATURE NAMES
-------------
Feature names are used in 'label', 'compute', 'set', and 'ignore' lines.
Example feature names are 'in0', 'temp2', 'in3_min', and 'temp3_over'.
These features are defined for each chip in lib/chips.c.
Undefined features will be silently ignored in 'label' and 'compute' lines.
Undefined features in 'set' lines will result in 'Unknown feature name'
when running 'sensors -s'.
Unfortunately, feature names starting with a number must be in
double quotes or you get "parse error, expecting 'NAME'".
LABEL LINES
-----------
A label line describes what a certain feature stands for on your
mainboard. Programs can retrieve these names and display them.
If no label is specified for a certain feature, the default name
(ie. 'fan1' for fan1) is used.
These are as advised in the LM78 and LM79 data sheets, and used on most
boards we have seen.
label in0 "VCore 1"
label in1 "VCore 2"
label in2 "+3.3V"
label in3 "+5V"
label in4 "+12V"
label in5 "-12V"
label in6 "-5V"
COMPUTE LINES
-------------
A compute line describes how to scale a certain feature. There are
two expressions in it: the first describes how the driver value must
be translated to a user value, the second how a user value must be
translated to a driver value. '@' is the value to operate on. You may
refer to other readable features (like 'cpu0_vid * 1.05').
The following operators are valid: + - * / ( ) ^ `
^ is e**x and ` is ln(x)
Where it makes sense, compute lines are inherited by subfeatures.
For example, the compute line for 'in0' is automatically applied to
'in0_min' and 'in0_max' as well.
VOLTAGE COMPUTATION DETAILS
---------------------------
Most voltage sensors in sensor chips have a range of 0 to 4.096 Volts.
This is generally sufficient for the 3.3 and CPU (2.5V, for example)
supply voltages, so the sensor chip reading is the actual voltage.
Other supply voltages must be scaled with an external resistor network.
The chip driver generally reports the 'raw' value 0 - 4.09 V, and the
userspace application must convert this raw value to an actual voltage.
The 'compute' lines provide this facility.
Unfortunately the resistor values vary among motherboard types.
Therefore you may have to adjust the computations in this file
to match your motherboard.
For positive voltages (in3, in4), two resistors are used, with the following
formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
R1 = R2 * (Vs/Vin - 1)
For negative voltages (in5, in6) two resistors are used, with the following
formula (Rin,Rf: resistor values, Vs: read voltage, Vin: pin voltage)
Rin = (Vs * Rf) / Vin
Note: Some chips use a different formula, see it87 section for example.
Here are the official LM78 and LM79 data sheet values.
Vs R1,Rin R2,Rf Vin
in3 +5.0 6.8 10 +2.98
in4 +12.0 30 10 +3.00
in5 -12.0 240 60 +3.00
in6 -5.0 100 60 +3.00
These would lead to these declarations:
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10)+1)*@ , @/((30/10)+1)
compute in5 -(240/60)*@ , -@/(240/60)
compute in6 -(100/60)*@ , -@/(100/60)
On almost any mainboard we have seen, the Winbond compute values lead to
much better results, though.
Vs R1,Rin R2,Rf Vin
in4 +12.0 28 10 +3.15
in5 -12.0 210 60.4 +3.45
in6 -5.0 90.9 60.4 +3.33
These leads to these declarations:
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((28/10)+1)*@ , @/((28/10)+1)
compute in5 -(210/60.4)*@ , -@/(210/60.4)
compute in6 -(90.9/60.4)*@ , -@/(90.9/60.4)
NOTE: On many motherboards, the -5V and -12V sensors are not connected.
Add ignore lines so these readings will not be displayed. For example:
ignore in5
ignore in6
TEMPERATURE COMPUTATION EXAMPLES
--------------------------------
There are two common ways to adjust temperature readings.
One is to adjust by a constant. The other is to change the
temperature sensor type.
Add 5 degrees to temperature sensor 1:
compute temp1 @+5,@-5
Sensor type adjustments (certain chips only):
set temp1_type 1 # PII/Celeron Diode
set temp1_type 2 # 3904 transistor
set temp1_type 3 # thermal diode
set temp1_type 4 # thermistor
set temp1_type 5 # AMD AMDSI
set temp1_type 6 # Intel PECI
Often, a temperature sensor is disconnected; disable it with an ignore line:
ignore temp3
SET LINES
---------
Set statements set things like limits. Complete expressions can be
used. Not everything can sensibly be set: setting 'in0', for example,
is impossible! These settings are put through the compute translations;
so if we specify '12.8' for in6, '3.2' will actually be written!
Important note: In the 'sensors' program, these only take effect
after running 'sensors -s'!!!
Here are some examples:
set in0_max cpu0_vid*1.05
set in0_min cpu0_vid*0.95
set temp1_max 40
set temp1_max_hyst 37
Think of tempx_max as 'alarm set' and tempx_max_hyst as 'alarm clear'
thresholds. In most cases the 'max' value should be higher than
the 'max_hyst' value by several degrees.
All the set statements from this file are commented out by default.
The reason is that the proper limits are highly system-dependent,
and writing improper limits may have all sorts of weird effects,
from beeping to CPU throttling to instant reboot. If you want to
actually set the limits, remove the comment marks.
IGNORE LINES
------------
Ignore statements tell certain features are not wanted. As with compute
statements, 'ignore in0' would also invalidate 'in0_max' and 'in0_min'.
'ignore' does not disable anything in the actual sensor chip; it
simply prevents the user program from accessing that data.
ignore in0
STATEMENT ORDER
---------------
Statements can go in any order, EXCEPT that some statements depend
on others. Dependencies could be either in the library or the driver.
A 'compute' statement must go before a 'set' statement
for the same feature or else the 'set' won't be computed correctly.
This is a library dependency.
A 'set fan1_div' statement must go before a 'set fan1_min' statement,
because the driver uses the divisor in calculating the minimum.
BUS LINES
---------
There is one other feature: the 'bus' statement. An example is below.
bus "i2c-0" "SMBus PIIX4 adapter at e800"
If we refer from now on to 'i2c-0' in 'chip' lines, this will run-time
be matched to this bus. So even if the PIIX4 is called 'i2c-5' at that
moment, because five other adapters were detected first, 'i2c-0' in
the config file would always only match this physical bus. In the above
config file, this feature is not needed; but the next lines would
only affect the LM75 chips on the PIIX4 adapter:
chip "lm75-i2c-0-*"
You can use "sensors --bus-list" to generate bus lines for your system.
BEEPS
-----
Some chips support alarms with beep warnings. When an alarm is triggered
you can be warned by a beeping signal through your computer speaker. It
is possible to enable beeps for all alarms on a chip using the following
line:
set beep_enable 1
or disable them using:
set beep_enable 0
1. 1. 2. Here begins the real configuration file

chip "lm78-*" "lm79-*" "w83781d-*"

These are as advised in the LM78 and LM79 data sheets, and used on almost
any mainboard we have seen.

   label in0 "VCore 1"
   label in1 "VCore 2"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "-12V"
   label in6 "-5V"

For positive voltages (in3, in4), two resistors are used, with the following
formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
R1 = R2 * (Vs/Vin - 1)
For negative voltages (in5, in6) two resistors are used, with the following
formula (Rin,Rf: resistor values, Vs: read voltage, Vin: pin voltage)
Rin = (Vs * Rf) / Vin
Here are the official LM78 and LM79 data sheet values.
Vs R1,Rin R2,Rf Vin
in3 +5.0 6.8 10 +2.98
in4 +12.0 30 10 +3.00
in5 -12.0 240 60 +3.00
in6 -5.0 100 60 +3.00
These would lead to these declarations:
compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
compute in4 ((30/10)+1)*@ , @/((30/10)+1)
compute in5 -(240/60)*@ , -@/(240/60)
compute in6 -(100/60)*@ , -@/(100/60)
On almost any mainboard we have seen, the Winbond compute values lead to
much better results, though.
Vs R1,Rin R2,Rf Vin
in4 +12.0 28 10 +3.15
in5 -12.0 210 60.4 +3.45
in6 -5.0 90.9 60.4 +3.33
These leads to these declarations:

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
   compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
   compute in5 -(210/60.4)*@  ,  -@/(210/60.4)
   compute in6 -(90.9/60.4)*@ ,  -@/(90.9/60.4)

Here, we assume the VID readings are valid, and we use a max. 5% deviation

set in0_min cpu0_vid*0.95
set in0_max cpu0_vid*1.05
set in1_min cpu0_vid*0.95
set in1_max cpu0_vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
set in5_min -12 * 0.95
set in5_max -12 * 1.05
set in6_min -5 * 0.95
set in6_max -5 * 1.05

Examples for lm78, lm79 temperature limits
set temp1_max 40
set temp1_max_hyst 37

Examples for w83781d temperature limits
set temp1_max 40
set temp1_max_hyst 37
set temp2_max 52
set temp2_max_hyst 47
set temp3_max 52
set temp3_max_hyst 47

Examples of fan low speed limits
set fan1_min 3000
set fan2_min 3000
set fan3_min 3000

Ignore fans you don't actually have
ignore fan1
ignore fan2
ignore fan3

In case a lm78 is used together with a lm75, the lm78 temp sensor will
generally show the M/B temperature while the lm75 temp sensor will show
the CPU temperature.
label temp1 "M/B Temp"

Uncomment the following line to enable beeps for all alarms on this chip
set beep_enable 1

chip "lm75-*"

Most boards don't need scaling. Following is for the Asus TX97-E.
compute temp1 @*2.0, @/2.0

Examples for temperature limits
set temp1_max 70
set temp1_max_hyst 65

In case a lm75 is used together with a lm78, the lm78 temp sensor will
generally show the M/B temperature while the lm75 temp sensor will show
the CPU temperature.
label temp1 "CPU Temp"

chip "sis5595-*"

   label in0 "VCore 1"
   label in1 "VCore 2"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
   compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)

set in0_min 2.0 * 0.95
set in0_max 2.0 * 1.05
set in1_min 2.0 * 0.95
set in1_max 2.0 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05

SiS5595 temperature calculation
The driver currently includes a calculation due to the wide
variation in thermistor types on SiS5595 motherboards.
The driver currently has a calculation of t = (.83x + 52.12).
One user reports the correct formula of t = (.345x - 12).
So you want to put a compute line in sensors.conf that has
the inverse of the driver formula, and put your formula on top of it.
The inverse of the driver formula is x = (1.20t - 62.77)
So the final formula is newt = (.345(1.20t - 62.77)) - 12).
Put this in the sensors.conf file as
compute temp1 ((.345 * ((1.20 * @) - 62.77)) - 12), ...
where ... is the inverse function I leave to you.
Look in your 'Vendor.ini' file to see which one is present
on your motherboard. Look for the line like:
[Temp1]
ThermistorType = NTC-10KC15-1608-1P
Fix up a 'compute' line to match your thermistor type.
Warning. You still don't have enough information to do this.
ThermistorType = NTC-10KC15-1608-1P (10K at 25C; Beta = 3435)
compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
ThermistorType = NTC-103KC15-1608-1P (??)
compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
ThermistorType = NTC-103AT-2 (10K at 25C; Beta = 3435)
compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...
ThermistorType = NTC-103JT (10K at 25C; Beta = 3435)
compute temp1 ((X * ((1.20 * @) - 62.77)) - Y), ...

examples for sis5595 temperature limits;
set temp1_max 40
set temp1_max_hyst 37

chip "w83782d-*" "w83627hf-*"

Same as above for w83781d except that in5 and in6 are computed differently.
Rather than an internal inverting op amp, the 82d/83s use standard positive
inputs and the negative voltages are level shifted by a 3.6V reference.
The math is convoluted, so we hope that your motherboard
uses the recommended resistor values.

   label in0 "VCore 1"
   label in1 "VCore 2"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "-12V"
   label in6 "-5V"
   label in7 "V5SB"
   label in8 "VBat"

Abit BP6 motherboard has a few differences. VCore1 and VCore2 are the core
voltages of the two processors. Vtt is memory bus termination resistors
voltage.
label in1 "Vtt"
label in8 "VCore2"

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
   compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
   compute in5 (5.14 * @) - 14.91  ,  (@ + 14.91) / 5.14
   compute in6 (3.14 * @) -  7.71  ,  (@ +  7.71) / 3.14
   compute in7 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)

set limits to 5% for the critical voltages
set limits to 10% for the non-critical voltages
set limits to 20% for the battery voltage

set in0_min cpu0_vid*0.95
set in0_max cpu0_vid*1.05
set in1_min cpu0_vid*0.95
set in1_max cpu0_vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_max -12 * 0.90
set in5_min -12 * 1.10
set in6_max -5 * 0.95
set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
set in8_min 3.0 * 0.80
set in8_max 3.0 * 1.20

set up sensor types (thermistor is default)
1 = PII/Celeron Diode; 2 = 3904 transistor;
3435 = thermistor with Beta = 3435
If temperature changes very little, try 1 or 2.
set temp1_type 1
set temp2_type 2
set temp3_type 3435

examples for temperature limits
set temp1_max 40
set temp1_max_hyst 37
set temp2_max 52
set temp2_max_hyst 47
set temp3_max 52
set temp3_max_hyst 47

chip "w83783s-*"

Same as above for w83781d except that in5 and in6 are computed differently.
Rather than an internal inverting op amp, the 82d/83s use standard positive
inputs and the negative voltages are level shifted by a 3.6V reference.
The math is convoluted, so we hope that your motherboard
uses the recommended resistor values.

   label in0 "VCore 1"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "-12V"
   label in6 "-5V"

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
   compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
   compute in5 (5.14 * @) - 14.91  ,  (@ + 14.91) / 5.14
   compute in6 (3.14 * @) -  7.71  ,  (@ +  7.71) / 3.14

set limits to 5% for the critical voltages
set limits to 10% for the non-critical voltages
set limits to 20% for the battery voltage

set in0_min cpu0_vid*0.95
set in0_max cpu0_vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_max -12 * 0.90
set in5_min -12 * 1.10
set in6_max -5 * 0.95
set in6_min -5 * 1.05

set up sensor types (thermistor is default)
1 = PII/Celeron Diode; 2 = 3904 transistor;
3435 = thermistor with Beta = 3435
If temperature changes very little, try 1 or 2.
set temp1_type 1
set temp2_type 2

examples for temperature limits
set temp1_max 40
set temp1_max_hyst 37
set temp2_max 52
set temp2_max_hyst 47

chip "w83697hf-*"

Same as above for w83781d except that in5 and in6 are computed differently.
Rather than an internal inverting op amp, the 82d/83s use standard positive
inputs and the negative voltages are level shifted by a 3.6V reference.
The math is convoluted, so we hope that your motherboard
uses the recommended resistor values.

no in1 on this chip.

   label in0 "VCore"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "-12V"
   label in6 "-5V"
   label in7 "V5SB"
   label in8 "VBat"

Tyan Trinity S2495 KT400 has a few differences. Thanks to Eric Schumann
for proving this information. Same is true for Epox 8K3A and 8KHA+.
Thanks to Thomas Schorpp for additional feedback.
label in2 "VAgp"
label in5 "+3.3V" # aka. Vio
label in6 "Vdimm"
label in7 "VBat"
label in8 "V5SB"
You'll also want to comment out the in5 and in6 compute lines right below,
and rename compute in7 to compute in8.

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
   compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
   compute in5 (5.14 * @) - 14.91  ,  (@ + 14.91) / 5.14
   compute in6 (3.14 * @) -  7.71  ,  (@ +  7.71) / 3.14
   compute in7 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)

697HF does not have VID inputs so you MUST set your core
voltage limits below. Currently set for 1.8V core.
vvv

set in0_min 1.8 * 0.95
set in0_max 1.8 * 1.05

set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_max -12 * 0.90
set in5_min -12 * 1.10
set in6_max -5 * 0.95
set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
set in8_min 3.0 * 0.80
set in8_max 3.0 * 1.20

And for Tyan Trinity S2495 KT400 and Epox 8K3A and 8KHA+:
set in2_min 1.5 * 0.95
set in2_max 1.5 * 1.05
set in5_min 3.3 * 0.95
set in5_max 3.3 * 1.05
set in6_min 2.5 * 0.95 # 2.6 on Epox
set in6_max 2.5 * 1.05 # 2.6 on Epox
set in7_min 3.0 * 0.90
set in7_max 3.0 * 1.10
set in8_min 5 * 0.90
set in8_max 5 * 1.10

set up sensor types (thermistor is default)
1 = PII/Celeron Diode; 2 = 3904 transistor;
3435 = thermistor with Beta = 3435
If temperature changes very little, try 1 or 2.
set temp1_type 1
set temp2_type 2
set temp3_type 3435

examples for temperature limits
set temp1_max 40
set temp1_max_hyst 37
set temp2_max 52
set temp2_max_hyst 47

chip "w83627thf-*" "w83637hf-*"

Rather than an internal inverting op amp, the 627thf uses standard positive
inputs and the negative voltages are level shifted by a 3.6V reference
(same as 82d/83s).
The math is convoluted, so we hope that your motherboard
uses the recommended resistor values.
Note that in1 (+12V) is the usual in4, and in4 (-12V) is the usual in5.
Data sheet is obviously wrong for in4, the usual formula should work.
No in5 nor in6.

   label in0 "VCore"
   label in1 "+12V"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "-12V"
   label in7 "V5SB"
   label in8 "VBat"

Mori Hiroyuki reported to need this (P4P800)
compute in0 @/2, @*2

   compute in1 ((28/10)+1)*@, @/((28/10)+1)
   compute in3 ((34/51)+1)*@, @/((34/51)+1)
   compute in4 (5.14*@)-14.91, (@+14.91)/5.14
   compute in7 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)

set limits to 5% for the critical voltages
set limits to 10% for the non-critical voltages
set limits to 20% for the battery voltage
if your vid is wrong, you'll need to adjust in0_min and in0_max

set in0_min cpu0_vid * 0.95
set in0_max cpu0_vid * 1.05
set in1_min 12 * 0.90
set in1_max 12 * 1.10
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min -12 * 1.10
set in4_max -12 * 0.90
set in7_min 5 * 0.95
set in7_max 5 * 1.05
set in8_min 3.0 * 0.80
set in8_max 3.0 * 1.20

set up sensor types (thermistor is default)
1 = PII/Celeron Diode; 2 = 3904 transistor;
3435 = thermistor with Beta = 3435
If temperature changes very little, try 1 or 2.
set temp1_type 1
set temp2_type 2
set temp3_type 3435

   label temp1 "M/B Temp"
   label temp2 "CPU Temp"

ignore temp3

examples for temperature limits
set temp1_max 40
set temp1_max_hyst 37
set temp2_max 52
set temp2_max_hyst 47
set temp3_max 52
set temp3_max_hyst 47

ignore fan1

   label fan2 "CPU Fan"

ignore fan3

Here are configurations for Winbond W83792AD/D chip.

chip "w83792d-*"

   label in0 "VCoreA"
   label in1 "VCoreB"
   label in2 "VIN0"
   label in3 "VIN1"
   label in4 "VIN2"
   label in5 "VIN3"
   label in6 "5VCC"
   label in7 "5VSB"
   label in8 "VBAT"
   label fan1 "Fan1"
   label fan2 "Fan2"
   label fan3 "Fan3"
   label fan4 "Fan4"
   label fan5 "Fan5"
   label fan6 "Fan6"
   label fan7 "Fan7"
   label temp1 "Temp1"
   label temp2 "Temp2"
   label temp3 "Temp3"

set in0_min 1.4
set in0_max 1.6
set in1_min 1.4
set in1_max 1.6
set in2_min 3.2
set in2_max 3.4
set in3_min 3.1
set in3_max 3.3
set in4_min 1.4
set in4_max 1.5
set in5_min 2.6
set in5_max 2.65
set in6_min 5 * 0.95
set in6_max 5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
set in8_min 3 * 0.95
set in8_max 3 * 1.05

fan1 adjustments examples

set fan1_div 4
set fan1_min 1500

temp2 limits examples

set temp2_max 42
set temp2_max_hyst 37

ignore examples

ignore fan7
ignore temp3

Here are configurations for Winbond W83793 chip.

chip "w83793-*"

   label in0 "VCoreA"
   label in1 "VCoreB"
   label in2 "Vtt"
   label in5 "+3.3V"
   label in6 "+12V"
   label in7 "+5V"
   label in8 "5VSB"
   label in9 "VBAT"

   compute in6 12*@ ,  @/12

   label temp1 "CPU1 Temp"
   label temp2 "CPU2 Temp"

fan1 adjustments examples

set fan1_min 1500

temp2 limits examples

set temp2_max 45
set temp2_max_hyst 40

ignore examples

ignore fan7
ignore temp3

chip "as99127f-*"

Asus won't release a datasheet so this is guesswork.
Thanks to Guntram Blohm, Jack, Ed Harrison, Artur Gawryszczak,
Victor G. Marimon and others for their feedback.

Dual power plane

   label in0 "VCore 1"
   label in1 "VCore 2"

Single power plane (A7V133, A7M266, CUV4X)
label in0 "VCore"
ignore in1

   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"

These last two may not make sense on all motherboards.

   label in5 "-12V"
   label in6 "-5V"

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
   compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)

AS99127F rev.1 (same as w83781d)

   compute in5 -(240/60.4)*@ ,  -@/(240/60.4)
   compute in6 -(90.9/60.4)*@ ,  -@/(90.9/60.4)

AS99127F rev.2 (same as w83782d)
compute in5 (5.14 * @) - 14.91 , (@ + 14.91) / 5.14
compute in6 (3.14 * @) - 7.71 , (@ + 7.71) / 3.14

Depending on your motherboard, you may have to use any of two formulae
for temp2. Quoting Artur Gawryszczak (edited to reflect subsequent fixes
to the driver):
"I guess, that the formula "(@*15/43)+25, (@-25)*43/15" is correct
for those Asus motherboards, which get CPU temperature from internal
thermal diode (Pentium Coppermine, and above), while no formula is needed
for Athlon/Duron boards, which use a thermistor in the socket."
An alternative formula was then found and reported by Victor G. Marimon.

Asus A7V133, Asus A7M266
No compute line is needed
Asus CUV4X, Asus A7V8X
compute temp2 (@*15/43)+25, (@-25)*43/15
Asus CUSL2, Asus CUV266-DLS, Asus TUSL2-C
compute temp2 (@*30/43)+25, (@-25)*43/30

See comments above if temp3 looks bad. What works for temp2 is likely
to work for temp3 for dual-CPU boards, such as the CUV4X-D.

Most Asus boards have temperatures settled like that:

   label temp1 "M/B Temp"
   label temp2 "CPU Temp"

However, some boards have them swapped (A7N8X Deluxe rev.2,
A7N8X-E Deluxe rev.2, CUV4X):
label temp1 "CPU Temp"
label temp2 "M/B Temp"

Most boards have no temp3 by default, except for dual-CPU boards.
label temp3 "CPU 2 Temp"
ignore temp3

set limits to 5% for the critical voltages
set limits to 10% for the non-critical voltages
set limits to 20% for the battery voltage

set in0_min cpu0_vid*0.95
set in0_max cpu0_vid*1.05
set in1_min cpu0_vid*0.95
set in1_max cpu0_vid*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_min -12 * 0.90
set in5_max -12 * 1.10
set in6_min -5 * 0.95
set in6_max -5 * 1.05

examples for temperature limits
set temp1_max 40
set temp1_max_hyst 37
set temp2_max 52
set temp2_max_hyst 47
set temp3_max 52
set temp3_max_hyst 47

chip "gl518sm-*"

IMPORTANT: in0, in1, and in2 values (+5, +3, and +12) CANNOT be read
Factors and labels taken from GL518SM datasheet, they seem to give
reasonable values with EISCA connected Fan78

 label in0 "+5V"
 label in1 "+3.3V"
 label in2 "+12V"
 label in3 "Vcore"

in2 depends on external resistors (4,7k and 15k assumed here)
in1 and in3 require no scaling

 compute in2 (197/47)*@  ,  @/(197/47)

set in0_min 4.8
set in0_max 5.2
set in1_min 3.20
set in1_max 3.40
set in2_min 11.0
set in2_max 13.0
set in3_min 2.10
set in3_max 2.30
set fan2_min 0

chip "gl520sm-*"

Factors and labels taken from GL520SM datasheet

The GL520SM has two application modes. In mode 1 it has two thermistor
inputs, in mode 2 it has only one and an extra (negative) voltage input.
The mode is supposed to be set properly by your BIOS so you should not
need to change it. Note that you have either temp2 or in4, not both.

 label in0 "+5V"
 label in1 "+3.3V"
 label in2 "+12V"
 label in3 "Vcore"
 label in4 "-12V"

in1 and in3 require no scaling
in2 depends on external resistors (4,7k and 15k assumed)

in4 = ((R1+R2)/R2)*@ - (R1/R2)*vdd
-12 --| R1 |---t---| R2 |-- +5
|
vin4

 compute in2 (197/47)*@  ,  @/(197/47)
 compute in4 (5*@)-(4*in0_input) , (@+4*in0_input)/5

set in0_min 4.8
set in0_max 5.2
set in1_min 3.20
set in1_max 3.40
set in2_min 11.0
set in2_max 13.0
set in3_min 2.10
set in3_max 2.30

chip "lm80-*"

The values below should be correct if you own a qdi BX (brilliant1)
mainboard. Many thanks go to Peter T. Breuer for helping us figure
out how to handle the LM80.

For positive voltages (in0..in4), two resistors are used, with the following
formula (R1,R2: resistor values, Vs: read voltage, Vin: pin voltage)
R1 = R2 * (Vs/Vin - 1)
For negative voltages (in5, in6) two resistors are used, with the following
formula (R3,R4: resistor values, Vs: read voltage, Vin: pin voltage,
V5: +5V)
R3 = R4 * (Vs - Vin) / (Vin - V5)

Here are the official LM80 data sheet values.
Vs R1,R3 R2,R4 Vin
+2.5V 23.7 75 +1.9
+3.3V 22.1 30 +1.9
+5.0 24 14.7 +1.9
+12.0 160 30.1 +1.9
-12.0 160 35.7 +1.9
-5.0 36 16.2 +1.9

Now curiously enough, VCore is connected with (unknown) resistors, which
translate a +2.8V to +1.9V. So we use that in the computations below.

   label in0 "+5V"
   label in1 "VTT"
   label in2 "+3.3V"
   label in3 "+Vcore"
   label in4 "+12V"
   label in5 "-12V"
   label in6 "-5V"

   compute in0 (24/14.7 + 1) * @ ,       @ / (24/14.7 + 1)
   compute in2 (22.1/30 + 1) * @ ,       @ / (22.1/30 + 1)
   compute in3 (2.8/1.9) * @,            @ * 1.9/2.8
   compute in4 (160/30.1 + 1) * @,       @ / (160/30.1 + 1)
   compute in5 (160/35.7)*(@ - in0_input) + @, (@ + in0_input * 160/35.7)/ (1 + 160/35.7)
   compute in6 (36/16.2)*(@ - in0_input) + @,  (@ + in0_input * 36/16.2) / (1 + 36/16.2)

set in0_min 5 * 0.95
set in0_max 5 * 1.05
What is your VTT? It is probably not this value...
set in1_min 2*0.95
set in1_max 2*1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
What is your VCore? It is probably not this value...
set in3_min 1.9 * 0.95
set in3_max 1.9 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
set in5_min -12 * 1.05
set in5_max -12 * 0.95
set in6_min -5 * 1.05
set in6_max -5 * 0.95

All 4 of these limits apply to the single temperature sensor.
"crit" may or may not do anything on your motherboard but it should
be set higher than the "max" thresholds.
set temp1_max_hyst 45
set temp1_max 52
set temp1_crit_hyst 57
set temp1_crit 62

chip "via686a-*"

VIA is very specific about the voltage sensor inputs, and our labels
reflect what they say. Unfortunately, they are not at all specific about
how to convert any of the register values to real units. Fortunately,
Jonathan Yew and Alex van Kaam came through with some data for temp
conversion and formulae for voltage conversion. However, the conversions
should be regarded as our best guess - YMMV.

On the Tyan S1598, the 2.5V sensor reads 0 and is not displayed in the BIOS.
Linas Vepstas reports that this sensor shows nothing of
interest on the Abit KA7 (Athlon), and is also not displayed in the BIOS.
Likewise, Johannes Drechsel-Burkhard reports that this
sensor is unavailable in the BIOS of his MSI K7T Pro (Thunderbird). So,
if you have one of these boards you may want to uncomment the 'ignore in1'
line below.

   label in0 "CPU core"
   label in1 "+2.5V"
   #ignore in1
   label in2 "I/O"
   label in3 "+5V"
   label in4 "+12V"

   label fan1  "CPU Fan"
   label fan2  "P/S Fan"

VIA suggests that temp3 is an internal temp sensor for the 686a. However,
on the Tyan S1598 as well as the Abit KA7 (Athalon), the absolute values
of the readings from that sensor are not valid. The readings do seem to
correlate with temp changes, but the conversion factor may be quite
different from temp1 & temp2 (as noted above, VIA has not provided
conversion info). So, you may wish to 'ignore temp3'.

Johannes Drechsel-Burkhard notes that on his MSI K7T Pro,
temp1 is the CPU temp and temp2 is the SYS temp. Hugo van der Merwe notes
the same for his Gigabyte GA-7DXC, Olivier Martin for his Gigabyte
GA-7ZM and Patrick Thomson for his Chaintech CT-5ATA.
Thomas Anglmaier notes: on Epox EP-7kxa temp2 is CPU and temp1 is SYS.

   label temp1 "SYS Temp"
   label temp2 "CPU Temp"
   label temp3 "SBr Temp"
   #ignore temp3

Set your CPU core limits here if the BIOS did not.

   #set in0_min 1.70 * 0.95
   #set in0_max 1.70 * 1.05

Other voltage values are standard so we can enforce the limits.

set in1_min 2.5 * 0.95
set in1_max 2.5 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5 * 0.9
set in3_max 5 * 1.1
set in4_min 12 * 0.9
set in4_max 12 * 1.1

Set your temp limits here. Remember, 'tempX_max' is the temp at which an
alarm is triggered, and 'tempX_max_hyst' is the temp at which an alarm turns off.
Setting tempX_max_hyst to a few degrees below the corresponding tempX_max
prevents an oscillation between alarm on and off states. This kind of
oscillation is known as hyteresis, thus the name. (You typically get the
most serious and troublesome hysteresis when a sensor triggers something to
reduce the temp, thus creating a negative feedback loop. Even without that,
we would still get some oscillation when the temp hovers around the limit
due to noise.)

set temp1_max_hyst 40
set temp1_max 45
set temp2_max_hyst 55
set temp2_max 60
set temp3_max_hyst 60
set temp3_max 65

You could set your fan limits too, but the defaults should be fine.

   #set fan1_min 5000
   #set fan2_min 5000

chip "adm1025-*" "ne1619-*"

The ADM1025 has integrated scaling resistors, rather
than external resistors common to most sensor devices.
These apply to the 6 voltage inputs in0-in5 (+2.5V, VCore,
+3.3V, +5V, +12V, VCC). As the scaling is fixed inside
the chip for these inputs, it is fairly certain that the
motherboard connections match these labels, and that the
driver computations are correct. Therefore they do not need to
be overridden here.

   label in0 "+2.5V"
   label in1 "VCore"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "VCC"

Tolerate a 5% deviance for CPU power-supply
set in1_min cpu0_vid * 0.95
set in1_max cpu0_vid * 1.05
Tolerate a 10% deviance for other voltages
set in0_min 2.5 * 0.90
set in0_max 2.5 * 1.10
set in2_min 3.3 * 0.90
set in2_max 3.3 * 1.10
set in3_min 5.0 * 0.90
set in3_max 5.0 * 1.10
set in4_min 12 * 0.90
set in4_max 12 * 1.10
set in5_min 3.3 * 0.90
set in5_max 3.3 * 1.10

Depending on how your chipset is hardwired, you may or may not have
+12V readings (will show as 0.0V if you don't have it).
ignore in4

VCC is the power-supply voltage of the ADM1025 chipset, generally
redundant with +3.3V so you may want to hide it.
ignore in5

Temperatures

   label temp1 "CPU Temp"
   label temp2 "M/B Temp"

set temp1_min 10
set temp1_max 60
set temp2_min 10
set temp2_max 45

chip "lm87-*" "adm1024-*"

The LM87 has integrated scaling resistors, rather
than external resistors common to most sensor devices.
These apply to the first 6 voltage inputs in0-in5
(+2.5, Vccp1, +3.3, +5, 12, +Vccp2). As the scaling is fixed inside
the chip for these inputs, it is fairly certain that the
motherboard connections match these labels, and that the
driver computations are correct. Therefore they do not need to
be overridden here.

  label in0  "+2.5V"
  label in1  "VCore"
  label in2  "+3.3V"
  label in3  "+5V"
  label in4  "+12V"

label in5 "VCore2"

  label fan1 "CPU Fan"

label fan2 "Case Fan"

  label temp1 "M/B Temp"
  label temp2 "CPU Temp"

label temp3 "AUX Temp"

set in1_min cpu0_vid * 0.95
set in1_max cpu0_vid * 1.05
set in2_min 3.3 * 0.92
set in2_max 3.3 * 1.08
set in3_min 5 * 0.92
set in3_max 5 * 1.08
set in4_min 12 * 0.90
set in4_max 12 * 1.10

These ones are mutually exclusive with temp3. If you have temp3,
comment out these lines as they will trigger errors on "sensors -s".
set in0_min 2.5 * 0.92
set in0_max 2.5 * 1.08
set in5_min cpu0_vid * 0.95
set in5_max cpu0_vid * 1.05

Increase fan clock dividers if your fans read 0 RPM while you know
they are connected and running.
set fan1_div 4
set fan2_div 4

set fan1_min 3000
set fan2_min 3000

set temp1_min 5
set temp1_max 65
set temp2_min 5
set temp2_max 70

Uncomment if you actually have temp3 (which means you don't have 2.5V
nor Vccp2, as they are mutually exclusive).
set temp3_min 5
set temp3_max 70

LM87 AIN1 and AIN2 Section
-12 and -5 may be reversed on your board, this is
just a guess, the datasheet gives no guidance.
label in6 "-12V"
label in7 "-5V"
compute in6 (7.50 * @) - 21.45 , (@ + 21.45) / 7.50
compute in7 (4.05 * @) - 10.07 , (@ + 10.07) / 4.05
set in6_min -12 * 0.95
set in7_min -5 * 0.95
set in6_max -12 * 1.05
set in7_max -5 * 1.05

chip "it87-*" "it8712-*"

The values below have been tested on Asus CUSI, CUM motherboards.

Voltage monitors as advised in the It8705 data sheet

   label in0 "VCore 1"
   label in1 "VCore 2"
   label in2 "+3.3V"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "-12V"
   label in6 "-5V"
   label in7 "Stdby"
   label in8 "VBat"

Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
to report the VCORE voltage approximately 0.05V higher than the board's
BIOS does. Although it doesn't make much sense physically, uncommenting
the next line should bring the readings in line with the BIOS' ones in
this case.
compute in0 -0.05+@ , @+0.05

If 3.3V reads around 1.65V, uncomment the following line:
compute in2 2*@ , @/2

   compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)

A number of Gigabyte boards (GA-8IPE1000Pro, GA-8KNXP, GA-7N400-L) use
a different resistor combination for +5V:
compute in3 ((10/10)+1)*@ , @/((10/10)+1)

   compute in4 ((30/10) +1)*@  , @/((30/10) +1)

For this family of chips the negative voltage equation is different from
the lm78. The chip uses two external resistor for scaling but one is
tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950
data sheet is wrong)
Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref.
Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage.

The next two are negative voltages (-12 and -5).
The following formulas must be used. Unfortunately the datasheet
does not give recommendations for Rin, Rf, but we can back into
them based on a nominal +2V input to the chip, together with a 4.096V Vref.
Formula:
actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf))
For -12V input use Rin/Rf = 6.68
For -5V input use Rin/Rf = 3.33
Then you can convert the forumula to a standard form like:

   compute in5 (7.67 * @) - 27.36  ,  (@ + 27.36) / 7.67
   compute in6 (4.33 * @) - 13.64  ,  (@ + 13.64) / 4.33

this much simpler version is reported to work for a
Elite Group K7S5A board
compute in5 -(36/10)*@, -@/(36/10)
compute in6 -(56/10)*@, -@/(56/10)

   compute in7 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)

set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min 2.4
set in1_max 2.6
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
set in5_max -12 * 0.95
set in5_min -12 * 1.05
set in6_max -5 * 0.95
set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05

   #the chip does not support in8 min/max

Temperature
Important - if your temperature readings are completely whacky
you probably need to change the sensor type.
Adujst and uncomment the appropriate lines below.
2 = thermistor; 3 = thermal diode; 0 = unused
set temp1_type 3
set temp2_type 3
set temp3_type 3
If a given sensor isn't used, you will probably want to ignore it
(see ignore statement right below).

   label temp1       "M/B Temp"

set temp1_max 40
set temp1_min 15

   label temp2       "CPU Temp"

set temp2_max 45
set temp2_min 15
ignore temp3

   label temp3       "Temp3"

set temp3_max 45
set temp3_min 15

The A7V8X-X has temperatures inverted, and needs a conversion for
CPU temp. Thanks to Preben Randhol for the formula.
label temp1 "CPU Temp"
label temp2 "M/B Temp"
compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893

The A7V600 also has temperatures inverted, and needs a different
conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula.
label temp1 "CPU Temp"
label temp2 "M/B Temp"
compute temp1 (@+128)/3, (3*@-128)

Fans
set fan1_min 0
set fan2_min 3000
ignore fan3
set fan3_min 3000

chip "it8716-*"

Voltages

   label  in0  "VCore"
   label  in1  "VDDR"
   label  in2  "+3.3V"    # VCC3
   label  in3  "+5V"      # VCC
   label  in4  "+12V"

label in5 "-12V"
label in6 "-5V"

   label  in7  "5VSB"     # VCCH
   label  in8  "VBat"

   compute in3  ((6.8/10)+1)*@ , @/((6.8/10)+1)
   compute in4  ((30/10)+1)*@  , @/((30/10)+1)

compute in5 (1+232/56)*@ - 4.096*232/56 , (@ + 4.096*232/56)/(1+232/56)
compute in6 (1+120/56)*@ - 4.096*120/56 , (@ + 4.096*120/56)/(1+120/56)

   compute in7  ((6.8/10)+1)*@ , @/((6.8/10)+1)

If vid (nominal CPU voltage) isn't correct, hardcode the correct value
instead.
set in0_min cpu0_vid * 0.95
set in0_max cpu0_vid * 1.05
set in1_min 1.8 * 0.95
set in1_max 1.8 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5 * 0.95
set in3_max 5 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
set in5_max -12 * 0.95
set in5_min -12 * 1.05
set in6_max -5 * 0.95
set in6_min -5 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
The chip does not support in8 min/max

Temperatures

If you are lucky, the BIOS has set the proper sensor types for you.
If your temperature readings are completely whacky you probably
need to change the sensor types. Adujst and uncomment the
appropriate lines below.
2 = thermistor; 3 = thermal diode; 0 = unused
set temp1_type 3
set temp2_type 3
set temp3_type 3

If a given sensor isn't used, you will probably want to ignore it
as well (see ignore statement right below).
The CPU sensor can be any of temp1, temp2 or temp3 - it's motherboard
dependent. Same for the motherboard temperature.

label temp1 "CPU Temp"
label temp2 "M/B Temp"
ignore temp3

set temp1_max 60
set temp1_min 10
set temp2_max 50
set temp2_min 10

Fans

The CPU fan can be any of fan1, fan2 or fan3 - it's motherboard
dependent. Same for the case fan.

label fan1 "CPU Fan"
label fan2 "Case Fan"
ignore fan3

set fan1_min 2000
set fan2_min 2000

chip "fscpos-*"

Fujitsu-Siemens Poseidon chip

Temperature

   label temp1       "Temp1/CPU"
   label temp2       "Temp2/MB"
   label temp3       "Temp3/AUX"

Fans

   label fan1        "Fan1"
   label fan2        "Fan2"
   label fan3        "Fan3"

Voltage

   label in0         "+12V"
   label in1         "+5V"
   label in2         "Battery"

chip "fscscy-*"

Fujitsu-Siemens Scylla chip

Temperature

   label temp1       "Temp1/CPU0"
   label temp2       "Temp2/CPU1"
   label temp3       "Temp3/MB"
   label temp4       "Temp4/AUX"

Fans

   label  fan1       "Fan1/CPU0"
   label  fan2       "Fan2/CPU0"
   label  fan3       "Fan3"
   label  fan4       "Fan4"
   label  fan5       "Fan5"
   label  fan6       "Fan6"

Voltage

   label in0         "+12V"
   label in1         "+5V"
   label in2         "+3.3V"

chip "fscher-*"

Fujitsu-Siemens Hermes chip

Temperature

   label temp1       "Temp1/CPU"
   label temp2       "Temp2/MB"
   label temp3       "Temp3/AUX"

Fans

   label fan1        "Fan1/PS"
   label fan2        "Fan2/CPU"
   label fan3        "Fan3/AUX"

Voltage

   label in0         "+12V"
   label in1         "+5V"
   label in2         "Battery"

Uncomment the computes line below when using the old fscher driver, leave
them commented when using the newer unified fschmd driver
M R O O M R
compute in0 (@ * (49 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (49 * 33)
compute in1 (@ * (20 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (20 * 33)
compute in2 (@ * (10 * 33) / 255) + (0 / 100), (@ - (0 / 100)) * 255 / (10 * 33)

chip "pcf8591-*"

values for the Philips PCF8591 chip
Analog inputs

You may discard ch2 and ch3 if you don't use them (depends on the input
configuration)
ignore in2
ignore in3

  label  in0         "Chan. 0"
  label  in1         "Chan. 1"
  label  in2         "Chan. 2"
  label  in3         "Chan. 3"

The driver assumes Vref = 2.56V and Agnd = 0V. If it doesn't match
your hardware, you have to use compute lines. The example below is
correct for Vref = 5.0V and Agnd = 0V.
compute in0 (@ * 500 / 256), (@ * 256 / 500)
compute in1 (@ * 500 / 256), (@ * 256 / 500)
compute in2 (@ * 500 / 256), (@ * 256 / 500)
compute in3 (@ * 500 / 256), (@ * 256 / 500)

chip "adm1021-*" "adm1023-*" "max1617-*" "max1617a-*" "thmc10-*" "lm84-*" "gl523sm-*" "mc1066-*"

  label temp1 		"Board Temp"
  label temp2		"CPU Temp"

set temp1_min 40
set temp1_max 70
set temp2_min 40
set temp2_max 70

chip "lm83-*"

  label temp1 "M/B Temp"
  label temp2 "D1 Temp"
  label temp3 "CPU Temp"
  label temp4 "D3 Temp"

ignore D1 and/or D3 readings if not used
ignore temp2
ignore temp4

change high limits to fit your needs
set temp1_max 55
set temp2_max 60
set temp3_max 65
set temp4_max 60

change critical limit to fit your needs
only one limit for all four temperatures
should be higher than each of the high limits above
set temp3_crit 85

chip "max1619-*"

  label temp1 "M/B Temp"
  label temp2 "CPU Temp"

change high and low limits to fit your needs
set temp2_min 10
set temp2_max 100

change critical limit and hysteresis to fit your needs
set temp2_crit 50
set temp2_crit_hyst 40

chip "lm90-*" "adm1032-*" "lm86-*" "max6657-*" "adt7461-*" "max6680-*"

  label temp1 "M/B Temp"
  label temp2 "CPU Temp"
  label temp1_crit "M/B Crit"
  label temp2_crit "CPU Crit"

change high and low limits to fit your needs
set temp1_min 10
set temp1_max 55
set temp2_min 10
set temp2_max 66

change critical limits to fit your needs
should be higher than the corresponding high limit above
set temp1_crit 75
set temp2_crit 85

change the hysteresis values (to critical limits) to fit your needs
note #1: hyst2 will be automatically set with the same delta
note #2: the internal register, which stores a single, relative value
for both channels, cannot hold values greater than 31, so the delta
between critical temperatures and respective absolute hysteresis can
never exceed this value
set temp1_crit_hyst 70

chip "lm99-*"

  label temp1 "G/C Temp"
  label temp2 "GPU Temp"
  label temp1_crit "G/C Crit"
  label temp2_crit "GPU Crit"

note #1: only the LM99 needs this; for a LM89, comment the compute line
out
note #2: there is no way for us to differentiate between a LM89 and a
LM99; you have to know what you have; LM99 are frequently found on
graphics cards, most notably nVidia ones

  compute temp2 @+16, @-16

change high and low limits to fit your needs
set temp1_min 10
set temp1_max 90
set temp2_min 10
set temp2_max 100

change critical limits to fit your needs
should be higher than the corresponding high limit above
set temp1_crit 100
set temp2_crit 110

change the hysteresis values (to critical limits) to fit your needs
note #1: hyst2 will be automatically set with the same delta
note #2: the internal register, which stores a single, relative value
for both channels, cannot hold values greater than 31, so the delta
between critical temperatures and respective absolute hysteresis can
never exceed this value
set temp1_crit_hyst 105

chip "lm63-*"

  label temp1       "M/B Temp"
  label temp2       "CPU Temp"
  label temp2_crit  "CPU Crit"
  label fan1        "CPU Fan"

Change limits to fit your needs. Note that temp2_crit is read-only.
set temp1_max 50
set temp2_min 10
set temp2_max 70
set temp2_crit_hyst 75
set fan1_min 2000

chip "vt1211-*"

   label in0 "+3.3V"
   label in1 "+2.5V"
   label in2 "VCore"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "+3.3V"

   label temp1 "CPU Temp"
   label temp2 "Int Temp"

   label fan1 "Case Fan"
   label fan2 "CPU Fan"

All voltage calculations have the form
compute inX @ * (1 + R1 / R2), @ / (1 + R1 / R2)
The following are the resistor values as recommended by VIA
Voltage R1 R2
------- ---- ----
VCore - - (no scaling)
3.3 6.8k 10k
2.5 2k 10k
5.0 14k 10k
12.0 47k 10k
The VT1211 internal 3.3V (in5) is scaled by the driver and doesn't
need to be adjusted here. VCore doesn't need scaling at all.

   compute in0  @ * (1 + 6.8 / 10),  @ / (1 + 6.8 / 10)
   compute in1  @ * (1 +   2 / 10),  @ / (1 +   2 / 10)
   compute in3  @ * (1 +  14 / 10),  @ / (1 +  14 / 10)
   compute in4  @ * (1 +  47 / 10),  @ / (1 +  47 / 10)

set in0_min 3.3 * 0.95
set in0_max 3.3 * 1.05
set in1_min 2.5 * 0.95
set in1_max 2.5 * 1.05
If your vid is wrong, hardcode the CPU voltage (e.g. 1.4)
set in2_min cpu0_vid * 0.97
set in2_max cpu0_vid * 1.03
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12.0 * 0.90
set in4_max 12.0 * 1.10

   set in5_min 3.3 * 0.95
   set in5_max 3.3 * 1.05

The temperature calculations are of the form
compute tempX (@ - Offset) / Gain, (@ * Gain) + Offset
The following are the gain and offset values as recommended by VIA
Diode Type Gain Offset
---------- ---- ------
Intel CPU 0.9528 88.638
0.9686 65.000 *)
VIA C3 Ezra 0.9528 83.869
VIA C3 Ezra-T 0.9528 73.869
*) These are the values from the previous sensors.conf. I don't know
where they came from or how they got derived.
The VT1211 internal temperature (temp2) is scaled by the driver
and doesn't need to be adjusted here.

   compute temp1  (@ - 73.869) / 0.9528,  (@ * 0.9528) + 73.869

The thermistor calculations are of the form
compute tempX 1 / (1 / 298.15 - (` Vmax / @ - 1)) / B) - 273.15, \
Vmax / (1 + (^ (B / 298.15 - B / (273.15 + @))))
B is the thermistor beta value, Vmax is the reference voltage, '^' is the
exp() operator and '`' is the ln() operator.
Given B = 3435 and Vmax = 2.2V and assuming that the thermistor forms a
resistor divider with a resistor equal to the thermistor's nominal value at
25 degrees C, the following compute lines can be used:

   compute temp3  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
   compute temp4  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
   compute temp5  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
   compute temp6  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
   compute temp7  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))

set temp1_max_hyst 80
set temp1_max 85
set temp2_max_hyst 60
set temp2_max 65
set temp3_max_hyst 60
set temp3_max 65
set temp4_max_hyst 40
set temp4_max 45

set fan1_min 3000
set fan2_min 3000

chip "vt8231-*"

   label in1 "+2.5V"
   label in2 "VCore"
   label in3 "+5V"
   label in4 "+12V"
   label in5 "+3.3V"

   label temp1 "CPU Temp"
   label temp2 "M/B Temp"

Here are the resistor values as recommended by VIA:
Voltage R1 R2
VCore no scaling
2.5 2k 10k
3.5 (3.3V ext.) 6.8k 10k
5.0 14k 10k
12.0 47k 10k

compute in0 @ * (1 + 6.8 / 10), @ / (1 + 6.8 / 10)

   compute in1  @ * (1 +   2 / 10),  @ / (1 +   2 / 10)
   compute in3  @ * (1 +  14 / 10),  @ / (1 +  14 / 10)
   compute in4  @ * (1 +  47 / 10),  @ / (1 +  47 / 10)

in5 is scaled internally so scaling is done by the driver.

set in0_min 2.5 * 0.95
set in0_max 2.5 * 1.05
set in1_min 2.5 * 0.95
set in1_max 2.5 * 1.05
Replace "2.0" with your nominal CPU voltage for in2.
set in2_min 2.0 * 0.95
set in2_max 2.0 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12.0 * 0.95
set in4_max 12.0 * 1.05
set in5_min 3.3 * 0.95
set in5_max 3.3 * 1.05

For Intel CPU:

   compute temp1  (@ - 65) / 0.9686,  (@ * 0.9686) + 65

For VIA EPIA CPU (provided by Roger Lucas):
compute temp1 (@ - 45) / 0.7809, (@ * 0.7809) + 45

Thermistor calculations
3435 is the thermistor beta, 2.2 is the reference voltage.
'^' is the e**x operator; '`' is the ln(x) operator
This assumes that the thermistor forms a resistor divider with a resistor
equal to its nominal value at 25 degrees C.

   compute temp2  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))
   compute temp3  1 / (1 / 298.15 - (` (2.2 / @ - 1)) / 3435) - 273.15, \
                  2.2 / (1 + (^ (3435 / 298.15 - 3435 / (273.15 + @))))

set temp1_max_hyst 60
set temp1_max 65
set temp2_max_hyst 40
set temp2_max 45

set fan1_min 3000
set fan2_min 3000

chip "smsc47m1-*"

SMSC LPC47M10x, LPC47M13x, LPC47M14x and LPC47B27x chips

set fan1_min 3000
set fan2_min 3000

chip "smsc47m192-*"

Temperature and voltage input from SMSC LPC47M192 and LPC47M997 chips
This example works on a Gigabyte K8U motherboard
Voltages are scaled internally, no computations needed

   label in0 "+2.5V"

set in0_min 2.5 * 0.95
set in0_max 2.5 * 1.05

   label in1 "VCore"

set in1_min cpu0_vid * 0.95
set in1_max cpu0_vid * 1.05

   label in2 "+3.3V"

set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05

   label in3 "+5V"

set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05

   label in4 "+12V"

set in4_min 12.0 * 0.95
set in4_max 12.0 * 1.05

   label in5 "VCC"

set in5_min 3.3 * 0.95
set in5_max 3.3 * 1.05

   label in6 "+1.5V"

set in6_min 1.5 * 0.95
set in6_max 1.5 * 1.05
ignore in6

   label in7 "+1.8V"

set in7_min 1.8 * 0.95
set in7_max 1.8 * 1.05
Haven't yet heard from any board that has 1.8V connected, so
this might be more appropriate:
ignore in7

   label temp1 "Chip Temp"

set temp1_min 0
set temp1_max 60

   label temp2 "CPU Temp"

set temp2_min 0
set temp2_max 60

   label temp3 "Sys Temp"

set temp3_min 0
set temp3_max 60

This example was tested vs. Asus P4S333

chip "asb100-*"

   label in0 "VCore 1"
   #set in0_min cpu0_vid * 0.95
   #set in0_max cpu0_vid * 1.05

   label in1 "VCore 2"
   ignore in1
   #set in1_min cpu0_vid * 0.95
   #set in1_max cpu0_vid * 1.05

   label in2 "+3.3V"
   #set in2_min 3.3 * 0.95
   #set in2_max 3.3 * 1.05

   label in3 "+5V"
   compute in3 1.68 * @ ,  @ / 1.68
   #set in3_min 5.0 * 0.95
   #set in3_max 5.0 * 1.05

   label in4 "+12V"
   compute in4 3.8 * @ , @ / 3.8
   #set in4_min 12  * 0.90
   #set in4_max 12  * 1.10

   label in5 "-12V (reserved)"
   #ignore in5
   compute in5 -@ * 3.97 ,  -@ / 3.97
   #set in5_max -12 * 0.90
   #set in5_min -12 * 1.10

   label in6 "-5V (reserved)"
   #ignore in6
   compute in6 -@ * 1.666 , -@ / 1.666
   #set in6_max -5  * 0.95
   #set in6_min -5  * 1.05

   label temp1 "M/B Temp"
   #set temp1_max      45
   #set temp1_max_hyst 40

   label temp2 "CPU Temp (Intel)"
   #ignore temp2
   #set temp2_max      60
   #set temp2_max_hyst 50

   # PWRTMP connector on P4S333, for external sensor
   label temp3 "Power Temp"
   #ignore temp3
   #set temp3_max      45
   #set temp3_max_hyst 40

   # Used for Athlon diode, ignore for P4S333
   label temp4 "CPU Temp (AMD)"
   #set temp4_max      60
   #set temp4_max_hyst 50
   #ignore temp4

   label fan1 "CPU Fan"
   #set fan1_div 4
   #set fan1_min 2000

   label fan2 "Chassis Fan"
   #set fan2_div 2
   #set fan2_min 4000

   label fan3 "Power Fan"
   #set fan3_div 2
   #set fan3_min 4000

Sample configuration for the Intel S845WD1-E
courtesy of Marcus Schopen

chip "lm85c-*" "adm1027-*" "adt7463-*" "lm85-*" "lm85b-*"

Voltage inputs
Depending on the hardware setup, the ADT7463 may not have in4.

  label in0   "V1.5"      # AGP on Intel S845WD1-E
  label in1   "VCore"
  label in2   "V3.3"
  label in3   "V5"
  label in4   "V12"

Temperature inputs

  label temp1  "CPU Temp"
  label temp2  "Board Temp"
  label temp3  "Remote Temp"

Fan inputs

  label fan1   "CPU_Fan"

label fan2 "Fan2"
label fan3 "Fan3"
label fan4 "Fan4"

Voltage scaling is done on-chip. No 'compute' directive
should be necessary. If in0 has external scaling set
it here.

compute in0 @ * 2.5, @ / 2.5

Adjust fans speeds for actual pulses per rev
compute fan1 @ * 2, @ / 2 # 1 pulse per rev
compute fan2 @ / 2, @ * 2 # 4 pulse per rev

Ignore fans you (or your motherboard) don't have
ignore fan2
ignore fan3
ignore fan4

Set voltage limits
set in0_min 1.5 * 0.95
set in0_max 1.5 * 1.05
set in1_min cpu0_vid * 0.95
set in1_max cpu0_vid * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05

Set Fan limits
set fan1_min 4000

Set Temp Limits
set temp1_min 10
set temp1_max 50
set temp2_min 10
set temp2_max 35
set temp3_min 10
set temp3_max 35

chip "pc87366-*"

Voltage inputs

  label in7   "Vsb"
  label in8   "Vdd"
  label in9   "Vbat"
  label in10  "AVdd"

  compute in7   @*2, @/2
  compute in8   @*2, @/2
  compute in10  @*2, @/2

These are the operating conditions as recommended by National
Semiconductor

  set in7_min   3.0
  set in7_max   3.6
  set in8_min   3.0
  set in8_max   3.6

set in9_min 2.4
set in9_max 3.6

  set in10_min  3.0
  set in10_max  3.6

Temperature inputs

  label temp1       "CPU0 Temp"
  label temp1_crit  "CPU0 Crit"
  label temp2       "CPU1 Temp"
  label temp2_crit  "CPU1 Crit"
  label temp3       "S-IO Temp"
  label temp3_crit  "S-IO Crit"

set temp1_min 0
set temp1_max 70
set temp1_crit 85
set temp2_min 0
set temp2_max 70
set temp2_crit 85
set temp3_min 0
set temp3_max 70
set temp3_crit 85

Thermistors
On some systems, thermistors are used instead of thermal diodes.
Note that these are the same pins used differently, so you really
can't have them all on a given system.
ignore temp1
ignore temp2

  ignore temp4
  ignore temp5
  ignore temp6

3435 is the thermistor beta.
This assumes that the thermistor forms a resistor divider with a resistor
equal to its nominal value at 25 degres Celsius. If not, change the values.
We also assume that you have a working in10 (which is forcibly enabled by
default). If not, use 3.3 instead, but you lose accuracy.

  compute temp4  3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \
                 in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15))))
  compute temp5  3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \
                 in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15))))
  compute temp6  3435 / (` (1 / (1 - @ / in10_input) - 1) + 3435 / 298.15) - 273.15, \
                 in10_input * (1 - 1 / (1 + (^ (3435 / (273.15 + @) - 3435 / 298.15))))

set temp4_min 0
set temp4_max 70
set temp4_crit 85
set temp5_min 0
set temp5_max 70
set temp5_crit 85
set temp6_min 0
set temp6_max 70
set temp6_crit 85

Fan inputs

Ignore fans you don't have
ignore fan2
ignore fan3

set fan1_min 2000
set fan2_min 2000
set fan3_min 2000

chip "adm1030-*"

  label temp1 "SYS Temp"
  label temp2 "CPU Temp"
  label temp1_crit "SYS Crit"
  label temp2_crit "CPU Crit"

set temp1_max 60
set temp2_max 70
set temp1_crit 85
set temp2_crit 85

  label fan1 "CPU Fan"

set fan1_min 2000

chip "adm1031-*"

  label temp1 "SYS Temp"
  label temp2 "CPU Temp"
  label temp3 "AUX Temp"
  label temp1_crit "SYS Crit"
  label temp2_crit "CPU Crit"
  label temp3_crit "AUX Crit"

set temp1_max 60
set temp2_max 70
set temp3_max 70
set temp1_crit 85
set temp2_crit 85
set temp3_crit 85

  label fan1 "CPU Fan"
  label fan2 "Case Fan"

set fan1_min 2000
set fan2_min 2000

chip "w83l785ts-*"

  label temp1 "CPU Diode"

chip "lm92-*"

  label temp1 "CPU Temp"

Change limits as you see fit
set temp1_min 14
set temp1_max 60
set temp1_crit 72
Hysteresis is computed from critical limit
The same relative hysteresis is used for all of low, high
and critical limits.
set temp1_crit_hyst 70

Winbond W83627EHF configuration originally contributed by Leon Moonen
This is for an Asus P5P800, voltages for A8V-E SE.

chip "w83627ehf-*" "w83627dhg-*"

   label in0 "VCore"
   label in2 "AVCC"
   label in3 "3VCC"
   label in7 "VSB"
   label in8 "VBAT"

+12V is in1 and +5V is in6 as recommended by datasheet

   compute in1 @*(1+(56/10)),  @/(1+(56/10))
   compute in6 @*(1+(22/10)),  @/(1+(22/10))

set in1_min 12.0*0.9
set in1_max 12.0*1.1
set in6_min 5.0*0.95
set in6_max 5.0*1.05

Set the 3.3V
set in2_min 3.3*0.95
set in2_max 3.3*1.05
set in3_min 3.3*0.95
set in3_max 3.3*1.05
set in7_min 3.3*0.95
set in7_max 3.3*1.05
set in8_min 3.3*0.95
set in8_max 3.3*1.05

Fans

  label fan1      "Case Fan"
  label fan2      "CPU Fan"
  label fan3      "Aux Fan"

ignore fan3
ignore fan4
set fan1_min 1200
set fan2_min 1700

Temperatures

  label temp1     "Sys Temp"
  label temp2     "CPU Temp"
  label temp3     "AUX Temp"

ignore temp3
set temp1_max 45
set temp1_max_hyst 40
set temp2_max 45
set temp2_max_hyst 40

Fintek F71805F/FG configuration
This is the recommended wiring and resistor values from the F71805F/FG
datasheet. Your motherboard manufacturer may or may not have followed
these.

chip "f71805f-*"

Voltages

  label in0 "+3.3V"
  label in1 "Vtt1.2V"
  label in2 "Vram"
  label in3 "Vchip"
  label in4 "+5V"
  label in5 "+12V"
  label in6 "Vcc1.5V"
  label in7 "Vcore"
  label in8 "5VSB"

  # in0 is scaled internally
  compute in2  @*(1+100/100), @/(1+100/100)
  compute in3  @*(1+100/47),  @/(1+100/47)
  compute in4  @*(1+200/47),  @/(1+200/47)
  compute in5  @*(1+200/20),  @/(1+200/20)
  compute in8  @*(1+200/47),  @/(1+200/47)

  # in0 is the chip's own VCC.
  set in0_min  3.0
  set in0_max  3.6

  #set in1_min  1.2 * 0.95
  #set in1_max  1.2 * 1.05
  #set in2_min  2.5 * 0.95
  #set in2_max  2.6 * 1.05
  #set in3_min  3.3 * 0.95
  #set in3_max  3.3 * 1.05
  #set in4_min  5.0 * 0.95
  #set in4_max  5.0 * 1.05
  #set in5_min 12.0 * 0.95
  #set in5_max 12.0 * 1.05
  #set in6_min  1.5 * 0.95
  #set in6_max  1.5 * 1.05
  # in7 nominal value depends on the CPU model
  #set in7_min  1.4 * 0.95
  #set in7_max  1.4 * 1.05
  #set in8_min  5.0 * 0.95
  #set in8_max  5.0 * 1.05

Fans

  label fan1 "CPU Fan"
  label fan2 "Sys Fan"
  label fan3 "Aux Fan"

  #set fan1_min 2100
  #set fan2_min 1400
  #set fan3_min 1400

Temperatures

  label temp1 "CPU Temp"
  label temp2 "Sys Temp"
  label temp3 "Aux Temp"

  #set temp1_max       60
  #set temp1_max_hyst  58
  #set temp2_max       50
  #set temp2_max_hyst  48
  #set temp3_max       50
  #set temp3_max_hyst  48

Abit Uguru sensor part configuration.
The Abit Uguru is relativly straight forward to configure.
label statements:
The voltage (in) temp and fan sensors are usualy in the same order as listed
in the BIOS, but not always!
compute statements:
The temp and fan sensors don't need any compute statements. Most voltage
inputs are directly connected to the IC and thus don't need an compute line
because the 0-3494 mV voltage given by the kernel driver is correct. The sen-
sors for higher voltages however are connect through a divider and measure
ranges of: 0-4361mV, 0-6248mV or 0-14510mV. Thus the measured voltages must
be multiplied by resp. 1.248, 1.788 or 4.153. 3.3 volt sources use the 1.248
mutiplier, 5 volt the 1.788 and 12 volt the 4.153.
set statements:
The Abit BIOS sets reasonable treshholds and allows changing them, thus
set statements may be ommited. The abituguru kernel driver does support
them if you want to add them.
The configuration below is for the Kv8Pro and AV8 this is the default as this
driver is developed and tested on a Kv8Pro.
Configurations for many other Abit boards can be found at:
http://www.lm-sensors.org/trac/wiki/Configurations/Abit
If your motherboard isn't listed there and you create a configuration for it
please add it there.

chip "abituguru-*"

  label in0 "CPU Core Voltage"
  label in1 "DDR Voltage"
  label in2 "DDR VTT Voltage"
  label in3 "NB Voltage"
  label in4 "SB Voltage"
  label in5 "HyperTransport Voltage"
  label in6 "AGP VDDQ Voltage"
  label in7 "ATX +5V"
  compute in7 @*1.788 , @/1.788
  label in8 "ATX +3.3V"
  compute in8 @*1.248 , @/1.248
  label in9 "Standby Voltage (+5V)"
  compute in9 @*1.788 , @/1.788
  label in10 "3VDual Voltage"
  compute in10 @*1.248 , @/1.248

  label temp1 "CPU Temperature"
  label temp2 "SYS Temperature"
  label temp3 "PWM Temperature"
  ignore temp4
  ignore temp5
  ignore temp6
  ignore temp7

  label fan1 "CPU FAN Speed"
  label fan2 "NB FAN Speed"
  label fan3 "SYS FAN Speed"
  label fan4 "AUX1 FAN Speed"
  label fan5 "AUX2 FAN Speed"
  ignore fan6

chip "k8temp-*"

  label temp1 "Core0 Temp"
  label temp2 "Core0 Temp"
  label temp3 "Core1 Temp"
  label temp4 "Core1 Temp"

Sample configuration for the SMSC DME1737 and ASUS A8000

chip "dme1737-*"

Voltage inputs

  label in0   "V5stby"
  label in1   "Vccp"
  label in2   "V3.3"
  label in3   "V5"
  label in4   "V12"
  label in5   "V3.3stby"
  label in6   "Vbat"

Temperature inputs

  label temp1   "RD1 Temp"
  label temp2   "Int Temp"
  label temp3   "CPU Temp"

Fan inputs

  label fan1   "CPU_Fan"
  label fan2   "Fan2"
  label fan3   "Fan3"
  label fan4   "Fan4"
  label fan5   "Fan5"
  label fan6   "Fan6"

Set voltage limits
set in0_min 5.0 * 0.95
set in0_max 5.0 * 1.05
set in1_min 1.4 * 0.95
set in1_max 1.4 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5.0 * 0.95
set in3_max 5.0 * 1.05
set in4_min 12.0 * 0.95
set in4_max 12.0 * 1.05
set in5_min 3.3 * 0.95
set in5_max 3.3 * 1.05
set in6_min 3.0 * 0.95
set in6_max 3.0 * 1.05

Set Temp Limits
set temp1_min 10
set temp1_max 75
set temp2_min 10
set temp2_max 75
set temp3_min 10
set temp3_max 75

Set Fan limits
set fan1_min 1000
set fan2_min 1000
set fan3_min 1000
set fan4_min 1000
set fan5_min 1000
set fan6_min 1000

sample configuration for the Fintek f71882fg and f71883fg
The configuration below is for the Epox EP-9U1697 GLI board, which has a
Fintek f71883fg relabeled as Epox ep1308, this is the default config as this
driver is developed and tested on an Epox EP-9U1697 GLI board.
Premade configurations for other boards can be found at:
http://www.lm-sensors.org/trac/wiki/Configurations/
If your motherboard isn't listed there and you create a configuration for it
please add it there.

chip "f71882fg-*"

Temperature

   label temp1       "CPU"
   label temp2       "System"
   ignore temp3

Fans

   label fan1        "CPU"
   label fan2        "System"
   label fan3        "Power"
   label fan4        "Aux"

Voltage

   label in0         "3.3V"
   label in1         "Vcore"
   label in2         "Vdimm"
   label in3         "Vchip"
   label in4         "+5V"
   label in5         "12V"
   label in6         "5VSB"
   label in7         "3VSB"
   label in8         "Battery"

never change the in0, in7 and in8 compute, these are hardwired in the chip!

   compute in0       (@ * 2), (@ / 2)
   compute in2       (@ * 2), (@ / 2)
   compute in3       (@ * 2), (@ / 2)
   compute in4       (@ * 5.25), (@ / 5.25)
   compute in5       (@ * 12.83), (@ / 12.83)
   compute in6       (@ * 5.25), (@ / 5.25)
   compute in7       (@ * 2), (@ / 2)
   compute in8       (@ * 2), (@ / 2)

chip "adm1022-*" "thmc50-*"

  label temp1 "M/B Temp"
  # Single CPU setup
  label temp2 "CPU Temp"

  # Dual CPU setup (ADM1022 only)
  #label temp2 "CPU0 Temp"
  #label temp3 "CPU1 Temp"

</source>

zurück | Hauptseite

Lenny/Dateiliste/sensors3.conf

/etc/sensors3.conf

Navigationsmenü

Suche